get the best experience
Replacement Part
This is an upgraded version of the OEM Clutch. Xtreme Mower Clutches, uses machined billet pulleys, upgraded bearings with high temperature grease, and a triple protected wire harnesses. The proprietary Xtreme Cool Coil technology reduces temperature to extend clutch life, and has a replaceable pulley bearing. Every Xtreme Clutch comes with a watertight integrated wire harness – PLUG and PLAY !
Xtreme Mower Clutches is a registered trademark of Extreme Mower Clutches Inc. (XMCI) of Boca Raton Florida. XMCI does not imply any association or affiliation with any OEM Manufacture including Warner Electric, Ogura Industrial Corp., John Deere, Exmark/Toro, Hustler, Husqvarna, Cub Cadet, or any of its associates or affiliates, trademarks or copyrights. XMCI also states “OEM Upgrade” or “Warner Upgrade” only refers to the billet pulley, the use of stainless steel braking rivets, replaceable pulley bearing, Xtreme wire protection system, and Cool coil technology, most of which are unique to the Xtreme Mower Clutch product line.
John Deere Original Equipment Guard Kit #BM20880
EXmark 103-3245 Electric clutch. Warner 5218-243 w/pigtail (5218-228 w/o pigtail) Old Warner # 5218-100. 1″ I.D., 7-1/8″ Pulley, 5/8″ Belt. This item cannot be returned. Replaces: EXMARK 103-3245 WARNER 5218-100 WARNER 5218-228 WARNER 5218-243
The Discovery 2200 Metal Detector by Bounty Hunter(R) is an ultra lightweight detector that features advanced discrimination and notching with 9-segment digital target identification and 1-touch zap to eliminate unwanted targets. This detector also offers all digital controls with an easy-to-read depth indicator and 4-tone audio feedback. Requires two 9V alkaline batteries.
These striking black metal urns are a classic way to dress up your patio or dining room. The mottled, faux-marble finish will vary from urn to urn, but the overall effect is consistent. These three urns are round and can be placed on the ground, tabletop or porch. Place a stunning flower arrangement in one, and frame it with smaller arrangements in the other two vases.
RSV – Triplex Plunger Pumps. Manifold: New high efficiency design concept. Forged brass for strength and no porosity for longer life and higher hydrostatic pressures. Bolts: Eight 6mm grade 8.8. Plungers: Ceramic coated stainless steel Crankcase: Precision die-cast, cooling fins and anodized for maximum heat dissipation. Bearings: Oversized for maximum life and load disbursement, needle bearing on the drive side and ball on the non-drive side. Each bearing is held in position on the crankshaft and crankcase by snap rings. this assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminated the crankshaft from floating. Valves, Seats and Springs: Stainless steel with specially designed Ultra Form cages to provide long life and positive seating. Seals and V-Packing’s: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load. Oil Seals: All are constructed of Buna-N Rubber. Plunger Rods: Stainless steel construction for strength (no plating to scrape off), O-ring plunger sealing system. Connecting Rods: One piece special alloy aluminum and bronze based, oversized for maximum strength, load disbursement and life. heavy pin are construction, for added load strength. 3000 PSI, 3 GPM, 3400 RPM, 3/4″ Hollow Shaft, F7 Gas, Unloader, Thermal Relief Valve, Detergent tube with filter, 3/8″ Quick Connect, 3/8″ nipple, 3/4″ F nut, Inlet filter.
This Fasco A1000 centrifugal blower accepts 115/230V, 60 Hz, 4-2.9/2-1.4 amps power input and has a sleeve bearing for blower motor shaft support. The two-speed, single inlet blower has a free air output rating of 1,000 cubic feet per minute (CFM) at 1,100 revolutions per minute (RPM). The blower produces 950 CFM of air flow at 0.1″ (inches water gauge) static pressure (SP), 920 CFM at 0.2″, 880 CFM at 0.3″, 850/799 CFM at 0.4″, 800/750 CFM at 0.5″, 730/700 CFM at 0.6″, 660/640 CFM at 0.7″, 580/500 CFM at 0.8″, 300/260 CFM at 0.9″, and 120/120 CFM at 1.0″. This centrifugal blower is Underwriters Laboratories (UL) recognized and Canadian Standards Association (CSA) certified for quality assurance and is suitable for use in heating and ventilation applications such as exhaust vent fans for furnaces.
| Specifications | |
|---|---|
| Motor | 2-speed, 115/230V, 60 Hz, 4-2.9/2-1.4 amp, sleeve bearing, dual voltage |
| Blower type | Centrifugal, single inlet |
| Free air output | 1,000 CFM at 1,100 RPM |
| CFM at static pressure (SP) | 950 CFM of air flow at 0.1″ SP, 920 CFM at 0.2″, 880 CFM at 0.3″, 850/799 CFM at 0.4″, 800/750 CFM at 0.5″, 730/700 CFM at 0.6″, 660/640 CFM at 0.7″, 580/500 CFM at 0.8″, 300/260 CFM at 0.9″, and 120/120 CFM at 1.0″ |
| Specifications met | UL recognized, CSA certified |
Fasco manufactures blowers and motors for heating, ventilation, and cooling systems. The company, founded in 1911, is headquartered in Springfield, MO.
This is an upgraded version of the OEM Clutch. Xtreme Mower Clutches, uses machined billet pulleys, upgraded bearings with high temperature grease, and a triple protected wire harnesses. The proprietary Xtreme Cool Coil technology reduces temperature to extend clutch life, and has a replaceable pulley bearing. Every Xtreme Clutch comes with a watertight integrated wire harness – PLUG and PLAY !
Xtreme Mower Clutches is a registered trademark of Extreme Mower Clutches Inc. (XMCI) of Boca Raton Florida. XMCI does not imply any association or affiliation with any OEM Manufacture including Warner Electric, Ogura Industrial Corp., John Deere, Exmark/Toro, Hustler, Husqvarna, Cub Cadet, or any of its associates or affiliates, trademarks or copyrights. XMCI also states “OEM Upgrade” or “Warner Upgrade” only refers to the billet pulley, the use of stainless steel braking rivets, replaceable pulley bearing, Xtreme wire protection system, and Cool coil technology, most of which are unique to the Xtreme Mower Clutch product line.